ADE Accenta G3 Manuel d'utilisateur télécharger pdf

Access codes

There are two User codes used in the system, all

are 4 digit and can be set to any number from

0000 to 9999, signified by:

The user 1 and 2 codes have the same operation

for testing, Setting and Unsetting, but user 1

code which is usually considered to be the

Managers code has the authority to add, change

or delete the user 2 code and Duress code.



User 1 code - 0123 factory set



User 2 code - not programmed.

How to operate Personal Attack

Personal Attack buttons on the keypad are used

to activate the alarm, irrespective of whether the

system is armed or not.

Press Simultaneously:

How to unset system in alarm

Enter your code. Entering the code will turn the

alarm off and the cause of the alarm will be

displayed. After investigation press Reset to

clear the indication.

Note: If the alarm indication does not

clear, then the system may need to be

reset by the installation engineer, contact

you installer for further information.

Programs 1, 2 and 3

The panel uses 3 Part Set routines known as

Programs. In each Program the exit mode can be

changed and the zone may be set up to have a

different function.

The examples below show how 3 typical

Programs could be used in a house.

Program 1 To arm all of the zones and become

Set as the user leaves the property and closes the

final door.

Program 2 To protect the perimeter of the

property in the evening and become Set after say

20 seconds.

Program 3 To protect the downstairs areas of

the house at night and become Set silently.

The above are purely examples. The installer has

the ability at the programming stage to configure

all the circuits to the customer’s exact

requirements.

2 4PI175 issue 1_6/01

Operating instructions Accenta/Optima G3 Intruder system

Access codes

Contents

Unset system indications - - - - - - - - - - - 1

Set System indication - - - - - - - - - - - - 1

Access codes - - - - - - - - - - - - - - - - 2

How to operate Personal Attack - - - - - - 2

How to unset system in alarm - - - - - - - 2

Programs 1, 2 and 3 - - - - - - - - - - - - - 2

How to set the system (on program 1) - - - 3

Push to Set Switch - - - - - - - - - - - - - - 3

Keyswitch Set - - - - - - - - - - - - - - - - 3

Faults during setting - - - - - - - - - - - - - 3

How to unset the system (turn off) - - - - - 3

How to set program1,2 or 3- - - - - - - - - 3

How to Quick set - - - - - - - - - - - - - - 4

How to Omit zone(s) on setting system - - - 4

Fire Alarm - - - - - - - - - - - - - - - - - 4

How to set Chime zone - - - - - - - - - - - 4

Operator’s Program mode - - - - - - - - - - 5

To exit operation at any time - - - - - - - - - 5

How to enter Operator’s program mode - - 5

How to view the event log - - - - - - - - - - 5

How to create/omit User 2 code - - - - - - - 6

How to change current user code - - - - - - 6

How to create/change/omit the Duress code - 6

How to carry out Alarm and Walk tests- - - 7

Servicing organisation details- - - - - - - - - 7

Quick Reference - - - - - - - - - - - - - - - 8

n n n n

Reset

n n n n

Bell

Alarm

FIRST ZONE IN ALARM

OTHER ZONES IN ALARM

Investigate the Alarm

Strobe Off

ALL ZONE

Day

1 2 3 4 5 6 7

Résumé du contenu

Page 1 - 2 4PI175 issue 1_6/01

Access codesThere are two User codes used in the system, allare 4 digit and can be set to any number from0000 to 9999, signified by:The user 1 and 2 c

Page 2 - Unset output

How to set the system (onprogram 1)The green Day indicator should be showing.Enter your codenumber and checkthat the system isclear (none of thezone i

Page 3 - How to set Chime Zones

How to Quick setDuring the exit period (on entering User code)the system may be Setquickly by pressing Set.This removes the exit timeperiod.If you omi

Page 4 - How to view the event log

Operator’s Program modeThe information below shows the programmableoptions available and how to change them.Once the programming mode has been accesse

Page 5 - 6 4PI175 issue 1_6/01

How to create/omit User 2 codeUser 1 code which is usually considered to bethe Managerscode has theauthority to add,change or deletethe user 2 code.Ho

Page 6 - Servicing

How to carry out Alarm and WalktestsThe alarm test functionallows you to test theStrobe, Bell, Low andhigh volume soundersof the system.The walk test

Page 7 - 8 4PI175 issue 1_6/01

Quick Reference8 4PI175 issue 1_6/01Operating instructions Accenta/Optima G3 Intruder systemQuick ReferenceThe panels conform to therequirements of th